[Buildroot] [git commit branch/next] board: add support for WarPboard
Thomas Petazzoni
thomas.petazzoni at free-electrons.com
Sat Aug 8 10:56:31 UTC 2015
commit: http://git.buildroot.net/buildroot/commit/?id=2c6e667caa845e3eef116fd2085f19fdb625a6f1
branch: http://git.buildroot.net/buildroot/commit/?id=refs/heads/next
This is a set of patch to add support for warpboard
(Freescale board based on imx6sl)
The patch contains :
- defconfig for warpboard
- linux patches from Fabio Estevam to fix device tree due to last change on
warpboard schematics (rev 1.12) and to fix kernel imx_v6_v7 defconfig which
use incorrect hci protocol
- specific firmware file for warpboard bluetooth
nvram : brcmfmac4330-sdio.txt
Origin of nvram config file for wifi :
https://github.com/Freescale/meta-fsl-arm-extra
[Thomas: misc rewording/improvements in the README file.]
Signed-off-by: Arthur LAMBERT <arthur at dreem.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni at free-electrons.com>
---
board/freescale/warpboard/README | 65 ++++++++++++
.../warpboard/patches/linux/0001-hciuart-h4.patch | 34 +++++++
.../linux/0002-replace-uart2-by-uart5.patch | 103 ++++++++++++++++++++
.../lib/firmware/brcm/brcmfmac4330-sdio.txt | 40 ++++++++
configs/warpboard_defconfig | 42 ++++++++
5 files changed, 284 insertions(+), 0 deletions(-)
diff --git a/board/freescale/warpboard/README b/board/freescale/warpboard/README
new file mode 100644
index 0000000..d826b2d
--- /dev/null
+++ b/board/freescale/warpboard/README
@@ -0,0 +1,65 @@
+Build
+=====
+
+First, configure Buildroot for your WarpBoard.
+ make warpboard_defconfig
+
+Build all components:
+ make
+
+You will find in ./output/images/ the following files:
+ - imx6sl-warp.dtb
+ - rootfs.tar
+ - u-boot.imx
+ - zImage
+
+Update uboot
+============
+
+- Put warpboard in USB download mode by closing the j2 jumper on the
+ daugther board
+
+- Load u-boot.imx in the WarpBoard by using the imx-usb-loader host utility:
+
+ $ ./output/host/usr/bin/imx_usb -c output/host/etc/imx-loader.d/ output/images/u-boot.imx
+
+- U-Boot will appear in minicom
+
+- Reset the U-Boot environment to its default:
+ => env default -f -a
+ => saveenv
+
+- Run the DFU toocommand in U-Boot:
+ => dfu 0 mmc 0
+
+- Transfer U-Boot into flash by running this command in host side:
+
+ $ sudo ./output/host/usr/bin/dfu-util -D output/images/u-boot.imx -a boot
+
+- remove power and put the WarpBoard back into normal boot mode by
+ opening the j2 jumper.
+
+Update linux & rootfs
+=====================
+
+Run the 'ums' command from the u6Boot prompt to mount the eMMC as mass
+storage and update zImage, device tree (imx6sl-warp.dtb) and rootfs
+file (rootfs.tar) :
+
+=> ums 0 mmc 0
+
+Put the zImage and DTB files in the warp-vfat partition and extract as
+root the rootfs.tar tarball in the warp-rootfs partition.
+
+Using bluetooth
+================
+
+Enable the bluez_utils or bluez5_utils package, and then run:
+
+$ hciattach /dev/ttymxc4 any
+$ hciconfig hci0 up
+
+Using Wifi
+==========
+
+$ ifconfig wlan0 up
diff --git a/board/freescale/warpboard/patches/linux/0001-hciuart-h4.patch b/board/freescale/warpboard/patches/linux/0001-hciuart-h4.patch
new file mode 100644
index 0000000..f47541b
--- /dev/null
+++ b/board/freescale/warpboard/patches/linux/0001-hciuart-h4.patch
@@ -0,0 +1,34 @@
+From f6878a437a5ba157fd087ef5e1874bdce5eca199 Mon Sep 17 00:00:00 2001
+From: Fabio Estevam <fabio.estevam at freescale.com>
+Date: Mon, 22 Jun 2015 16:37:34 -0300
+Subject: [PATCH] ARM: imx_v6_v7_defconfig: Select HCIUART_H4
+
+The old warp board revision had hardware issues that prevented
+the RTS/CTS lines to work with the Bluetooth module.
+
+Tha latest rev1.12 fixes this problem, so now we should better use
+CONFIG_BT_HCIUART_H4 instead, as it provides a better throughput than
+the CONFIG_BT_HCIUART_3WIRE option.
+
+Suggested-by: Arthur Lambert <arthur at dreem.com>
+Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
+---
+ arch/arm/configs/imx_v6_v7_defconfig | 2 +-
+ 1 file changed, 1 insertion(+), 1 deletion(-)
+
+diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
+index f6989fb..c864295 100644
+--- a/arch/arm/configs/imx_v6_v7_defconfig
++++ b/arch/arm/configs/imx_v6_v7_defconfig
+@@ -73,7 +73,7 @@ CONFIG_CAN=y
+ CONFIG_CAN_FLEXCAN=y
+ CONFIG_BT=y
+ CONFIG_BT_HCIUART=y
+-CONFIG_BT_HCIUART_3WIRE=y
++CONFIG_BT_HCIUART_H4=y
+ CONFIG_CFG80211=y
+ CONFIG_CFG80211_WEXT=y
+ CONFIG_MAC80211=y
+--
+1.9.1
+
diff --git a/board/freescale/warpboard/patches/linux/0002-replace-uart2-by-uart5.patch b/board/freescale/warpboard/patches/linux/0002-replace-uart2-by-uart5.patch
new file mode 100644
index 0000000..d742c24
--- /dev/null
+++ b/board/freescale/warpboard/patches/linux/0002-replace-uart2-by-uart5.patch
@@ -0,0 +1,103 @@
+From: Fabio Estevam <fabio.estevam at freescale.com>
+Date: Fri, 29 May 2015 16:19:39 -0300
+Subject: [PATCH] ARM: dts: imx6sl-warp: Add changes for rev1.12
+
+Signed-off-by: Fabio Estevam <fabio.estevam at freescale.com>
+---
+ arch/arm/boot/dts/imx6sl-warp.dts | 32 +++++++++++++++++++-------------
+ 1 file changed, 19 insertions(+), 13 deletions(-)
+
+diff --git a/arch/arm/boot/dts/imx6sl-warp.dts b/arch/arm/boot/dts/imx6sl-warp.dts
+index 0da906b..bdfa82b 100644
+--- a/arch/arm/boot/dts/imx6sl-warp.dts
++++ b/arch/arm/boot/dts/imx6sl-warp.dts
+@@ -61,7 +61,9 @@
+ usdhc3_pwrseq: usdhc3_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>, /* WL_REG_ON */
++ <&gpio4 7 GPIO_ACTIVE_LOW>, /* WL_HOSTWAKE */
+ <&gpio3 25 GPIO_ACTIVE_LOW>, /* BT_REG_ON */
++ <&gpio3 27 GPIO_ACTIVE_LOW>, /* BT_HOSTWAKE */
+ <&gpio4 4 GPIO_ACTIVE_LOW>, /* BT_WAKE */
+ <&gpio4 6 GPIO_ACTIVE_LOW>; /* BT_RST_N */
+ };
+@@ -73,16 +75,16 @@
+ status = "okay";
+ };
+
+-&uart2 {
++&uart3 {
+ pinctrl-names = "default";
+- pinctrl-0 = <&pinctrl_uart2>;
+- fsl,uart-has-rtscts;
++ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+ };
+
+-&uart3 {
++&uart5 {
+ pinctrl-names = "default";
+- pinctrl-0 = <&pinctrl_uart3>;
++ pinctrl-0 = <&pinctrl_uart5>;
++ fsl,uart-has-rtscts;
+ status = "okay";
+ };
+
+@@ -130,14 +132,6 @@
+ >;
+ };
+
+- pinctrl_uart2: uart2grp {
+- fsl,pins = <
+- MX6SL_PAD_EPDC_D12__UART2_RX_DATA 0x41b0b1
+- MX6SL_PAD_EPDC_D13__UART2_TX_DATA 0x41b0b1
+- MX6SL_PAD_EPDC_D14__UART2_RTS_B 0x4130B1
+- MX6SL_PAD_EPDC_D15__UART2_CTS_B 0x4130B1
+- >;
+- };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+@@ -146,6 +140,15 @@
+ >;
+ };
+
++ pinctrl_uart5: uart5grp {
++ fsl,pins = <
++ MX6SL_PAD_ECSPI1_SCLK__UART5_RX_DATA 0x41b0b1
++ MX6SL_PAD_ECSPI1_MOSI__UART5_TX_DATA 0x41b0b1
++ MX6SL_PAD_ECSPI1_MISO__UART5_RTS_B 0x4130b1
++ MX6SL_PAD_ECSPI1_SS0__UART5_CTS_B 0x4130b1
++ >;
++ };
++
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6SL_PAD_SD2_CMD__SD2_CMD 0x417059
+@@ -158,6 +161,7 @@
+ MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x417059
+ MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x417059
+ MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x417059
++ MX6SL_PAD_SD2_RST__SD2_RESET 0x417059
+ >;
+ };
+
+@@ -173,6 +177,7 @@
+ MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x4170b9
+ MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x4170b9
+ MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x4170b9
++ MX6SL_PAD_SD2_RST__SD2_RESET 0x4170b9
+ >;
+ };
+
+@@ -188,6 +193,7 @@
+ MX6SL_PAD_SD2_DAT5__SD2_DATA5 0x4170f9
+ MX6SL_PAD_SD2_DAT6__SD2_DATA6 0x4170f9
+ MX6SL_PAD_SD2_DAT7__SD2_DATA7 0x4170f9
++ MX6SL_PAD_SD2_RST__SD2_RESET 0x4170f9
+ >;
+ };
+
+--
+1.9.1
+
diff --git a/board/freescale/warpboard/rootfs_overlay/lib/firmware/brcm/brcmfmac4330-sdio.txt b/board/freescale/warpboard/rootfs_overlay/lib/firmware/brcm/brcmfmac4330-sdio.txt
new file mode 100644
index 0000000..9546246
--- /dev/null
+++ b/board/freescale/warpboard/rootfs_overlay/lib/firmware/brcm/brcmfmac4330-sdio.txt
@@ -0,0 +1,40 @@
+# bcm94330wlsdgb.txt
+manfid=0x2d0
+prodid=0x0552
+vendid=0x14e4
+devid=0x4360
+boardtype=0x0552
+boardrev=0x11
+# this design has 2.4GHz SP3T switch
+boardflags=0x00080200
+nocrc=1
+xtalfreq=37400
+boardnum=22
+macaddr=00:90:4c:c5:12:38
+ag0=255
+aa2g=1
+ccode=CN
+pa0b0=0x14d0
+pa0b1=0xfd98
+pa0b2=0xff78
+rssismf2g=0xa
+rssismc2g=0x3
+rssisav2g=0x7
+maxp2ga0=0x50
+sromrev=3
+il0macaddr=00:90:4c:c5:12:38
+wl0id=0x431b
+cckPwrOffset=5
+ofdm2gpo=0x66666666
+mcs2gpo0=0x6666
+mcs2gpo1=0x6666
+swctrlmap_2g=0x04040404,0x02020202,0x02020404,0x10202,0x1ff
+swctrlmap_5g=0x00100010,0x00280020,0x00200010,0x14202,0x2f8
+rfreg033=0x19
+rfreg033_cck=0x1f
+dacrate2g=160
+txalpfbyp2g=1
+bphyscale=17
+cckPwrIdxCorr=-15
+pacalidx2g=45
+txgaintbl=1
diff --git a/configs/warpboard_defconfig b/configs/warpboard_defconfig
new file mode 100644
index 0000000..13e90cd
--- /dev/null
+++ b/configs/warpboard_defconfig
@@ -0,0 +1,42 @@
+# architecture
+BR2_arm=y
+BR2_cortex_a9=y
+
+# patches
+BR2_GLOBAL_PATCH_DIR="board/freescale/warpboard/patches/"
+
+# lock to 4.0 headers to avoid breaking with newer kernels
+BR2_KERNEL_HEADERS_VERSION=y
+BR2_DEFAULT_KERNEL_VERSION="4.0"
+BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_4_0=y
+
+# system
+BR2_TARGET_GENERIC_HOSTNAME="warpboard"
+BR2_TARGET_GENERIC_GETTY_PORT="ttymxc0"
+
+# rootfs overlay
+BR2_ROOTFS_OVERLAY="board/freescale/warpboard/rootfs_overlay"
+
+# kernel
+BR2_LINUX_KERNEL=y
+BR2_LINUX_KERNEL_CUSTOM_TARBALL=y
+BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="http://github.com/Freescale/linux-fslc/tarball/38ec11d/linux-fslc-38ec11d.tar.gz"
+BR2_LINUX_KERNEL_DEFCONFIG="imx_v6_v7"
+BR2_LINUX_KERNEL_ZIMAGE=y
+BR2_LINUX_KERNEL_DTS_SUPPORT=y
+BR2_LINUX_KERNEL_INTREE_DTS_NAME="imx6sl-warp"
+
+# wifi firmware for brcm4330
+BR2_PACKAGE_LINUX_FIRMWARE=y
+BR2_PACKAGE_LINUX_FIRMWARE_BRCM_BCM43XX=y
+
+# uboot
+BR2_TARGET_UBOOT=y
+BR2_TARGET_UBOOT_BOARDNAME="warp"
+BR2_TARGET_UBOOT_CUSTOM_VERSION=y
+BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2015.07-rc2"
+BR2_TARGET_UBOOT_FORMAT_IMX=y
+
+# host utility
+BR2_PACKAGE_HOST_DFU_UTIL=y
+BR2_PACKAGE_HOST_IMX_USB_LOADER=y
More information about the buildroot
mailing list