[Buildroot] [PATCH v3 4/4] configs/stm32mp157c-dk2: add support for wifi
Shlomi Vaknin
shlomi.39sd at gmail.com
Mon Oct 12 17:35:16 UTC 2020
Hi,
I agree. Do I need to send the other patches again?
Shlomi
בתאריך יום ב׳, 12 באוק׳ 2020 ב-17:49 מאת Bartosz Bilas <
b.bilas at grinn-global.com>:
> Hi Shlomi,
> On 10.10.2020 22:48, Shlomi Vaknin wrote:
>
> Hi Bartek,
>
> I did as you said and it didn't work. Here are the steps I did:
>
> 1. I changed as you said - didn't work.
> 2. I flashed the original image from st - works.
> 3. I flashed again the buildroot image - works.
> 4. I did hard reset - not working.
>
> Can you verify that you have this experience?
>
> Let's put this topic off for now because it blocks the rest of the patches
> that look good and can be merged. I need more time to check what exactly is
> going on with this wlan module.
> Best
> Bartek
>
>
> בתאריך שבת, 10 באוק׳ 2020 ב-22:01 מאת Bartosz Bilas <
> b.bilas at grinn-global.com>:
>
>> Hi Shlomi,
>> On 10.10.2020 17:41, Bartosz Bilas wrote:
>>
>> Hello Shlomi,
>> On 09.10.2020 21:13, Shlomi Vaknin wrote:
>>
>> HI!
>>
>> According to u-boot I have the same revision as you. Could you try the
>> formal version from st:
>> https://www.st.com/en/embedded-software/stm32mp1starter.html ? I flashed
>> it and the wifi worked. Just to be sure that there is no issue or something
>> else with your board.
>>
>> Best
>> Shlomi
>>
>> I've used:
>>
>> ST OpenSTLinux - Weston - (A Yocto Project Based Distro)
>> 3.1-openstlinux-5.4-dunfell-mp1-20-06-24 stm32mp1 ttySTM0
>>
>> and everything seems to be ok
>>
>> root at stm32mp1:~# ifconfig -a
>> eth0 Link encap:Ethernet HWaddr 00:80:E1:42:56:44
>> UP BROADCAST MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>> Interrupt:48 Base address:0x4000
>>
>> lo Link encap:Local Loopback
>> inet addr:127.0.0.1 Mask:255.0.0.0
>> inet6 addr: ::1/128 Scope:Host
>> UP LOOPBACK RUNNING MTU:65536 Metric:1
>> RX packets:80 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:80 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:6080 (5.9 KiB) TX bytes:6080 (5.9 KiB)
>>
>> usb0 Link encap:Ethernet HWaddr 4E:12:37:C3:7B:6C
>> UP BROADCAST MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>
>> wlan0 Link encap:Ethernet HWaddr 10:98:C3:5F:FB:F9
>> BROADCAST MULTICAST MTU:1500 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>
>> I'm gonna double-check one more time what's wrong with buildroot's image
>> though.
>> Best
>> Bartek
>>
>> I've got this working fine, I had to add
>> BR2_PACKAGE_MURATA_CYW_FW_CYW43430 instead of
>> BR2_PACKAGE_LINUX_FIRMWARE_BRCM_BCM43XXX as I mentioned before, I also
>> added BR2_PACKAGE_WPA_SUPPLICANT_PASSPHRASE
>>
>> and I've successfully connected with my wifi network.
>>
>> # ifconfig
>> lo Link encap:Local Loopback
>> inet addr:127.0.0.1 Mask:255.0.0.0
>> inet6 addr: ::1/128 Scope:Host
>> UP LOOPBACK RUNNING MTU:65536 Metric:1
>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>
>> wlan0 Link encap:Ethernet HWaddr 10:98:C3:5F:FB:F9
>> inet addr:192.168.10.110 Bcast:192.168.10.255
>> Mask:255.255.255.0
>> inet6 addr: fd3a:e7f5:fc04:0:1298:c3ff:fe5f:fbf9/64 Scope:Global
>> inet6 addr: fe80::1298:c3ff:fe5f:fbf9/64 Scope:Link
>> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
>> RX packets:8 errors:0 dropped:0 overruns:0 frame:0
>> TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
>> collisions:0 txqueuelen:1000
>> RX bytes:1624 (1.5 KiB) TX bytes:1988 (1.9 KiB)
>>
>> # ping google.com
>> PING google.com (216.58.215.78): 56 data bytes
>> 64 bytes from 216.58.215.78: seq=0 ttl=116 time=29.594 ms
>> 64 bytes from 216.58.215.78: seq=1 ttl=116 time=39.401 ms
>> ^C
>> --- google.com ping statistics ---
>> 2 packets transmitted, 2 packets received, 0% packet loss
>> round-trip min/avg/max = 29.594/34.497/39.401 ms
>>
>>
>> Could you verify if it works well on your device?
>>
>> בתאריך יום ו׳, 9 באוק׳ 2020 ב-19:49 מאת Bartosz Bilas <
>> b.bilas at grinn-global.com>:
>>
>>> Hello Shlomi,
>>> On 08.10.2020 22:45, Shlomi Vaknin wrote:
>>>
>>> Hi Bartek,
>>>
>>> I pulled the latest commits, downloaded my patches from patchwork and
>>> applied them. Then, I started a new out of tree build and everything is
>>> working. You can find my sdcard image here:
>>> https://drive.google.com/drive/folders/1_FwVtw70iPS_hz7yFiiOlhXiUKlsi9bH?usp=sharing
>>>
>>> This problem is very strange. Maybe you can check if your board's wifi
>>> is working with an image that is known to work? Maybe the formal image from
>>> st?
>>>
>>> Regards,
>>> Shlomi
>>>
>>> I've tested your image but the result is the same, see:
>>>
>>> [ 129.691504] cfg80211: Loading compiled-in X.509 certificates for
>>> regulatory database
>>> [ 129.740878] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
>>> # [ 129.804593] brcmfmac: brcmf_fw_alloc_request: using
>>> brcm/brcmfmac43430-sdio for chip BCM43430/1
>>> [ 130.885129] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
>>> clkctl 0x50
>>> [ 131.911135] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
>>> clkctl 0x50
>>>
>>> My board is:
>>>
>>> CPU: STM32MP157CAC Rev.B
>>> Model: STMicroelectronics STM32MP157C-DK2 Discovery Board
>>> Board: stm32mp1 in trusted mode (st,stm32mp157c-dk2)
>>> Board: MB1272 Var2.0 Rev.C-01
>>> DRAM: 512 MiB
>>> Best
>>> Bartek
>>>
>>> בתאריך יום ה׳, 8 באוק׳ 2020 ב-20:31 מאת Bartosz Bilas <
>>> b.bilas at grinn-global.com>:
>>>
>>>> Hi Shlomi,
>>>> On 07.10.2020 22:16, Shlomi Vaknin wrote:
>>>>
>>>> Hi Bartek,
>>>>
>>>> That is very strange, since it works for me:
>>>>
>>>>
>>>> #############################################################################################################################
>>>> Starting mdev... OK
>>>> [ 4.168709] cfg80211: Loading compiled-in X.509 certificates for
>>>> regulatory database
>>>> [ 4.224122] cfg80211: Loaded X.509 cert 'sforshee:
>>>> 00b28ddf47aef9cea7'
>>>> [ 4.288641] brcmfmac: brcmf_fw_alloc_request: using
>>>> brcm/brcmfmac43430-sdio for chip BCM43430/1
>>>> [ 4.486998] brcmfmac: brcmf_fw_alloc_request: using
>>>> brcm/brcmfmac43430-sdio for chip BCM43430/1
>>>> [ 4.501649] brcmfmac: brcmf_c_process_clm_blob: no clm_blob
>>>> available (err=-2), device may have limited channels available
>>>> [ 4.536998] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43430/1
>>>> wl0: Oct 23 2017 03:55:53 version 7.45.98.38 (r674442 CY) FWID 01-e58d219f
>>>>
>>>> # ifconfig -a
>>>> eth0 Link encap:Ethernet HWaddr 00:80:E1:42:58:DB
>>>> BROADCAST MULTICAST MTU:1500 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>> Interrupt:49 Base address:0xe000
>>>>
>>>> lo Link encap:Local Loopback
>>>> inet addr:127.0.0.1 Mask:255.0.0.0
>>>> inet6 addr: ::1/128 Scope:Host
>>>> UP LOOPBACK RUNNING MTU:65536 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>
>>>> sit0 Link encap:IPv6-in-IPv4
>>>> NOARP MTU:1480 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>
>>>> wlan0 Link encap:Ethernet HWaddr 00:9D:6B:A6:BC:BA
>>>> BROADCAST MULTICAST MTU:1500 Metric:1
>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>> collisions:0 txqueuelen:1000
>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>
>>>> #############################################################################################################################
>>>>
>>>> The nvram configuration file was directly copied from the bsp layer of
>>>> st in yocto (dunfell):
>>>> https://github.com/STMicroelectronics/meta-st-stm32mp/blob/dunfell/recipes-kernel/linux-firmware/linux-firmware/brcmfmac43430-sdio.txt
>>>>
>>>> Regards,
>>>> Shlomi
>>>>
>>>> So in that case we have to clarify our environments. Have you tested
>>>> using the latest master branch or is it some tagged version? Could you do a
>>>> clean build once again to be sure that you don't use any cached things? If
>>>> you were able to attach your sdcard image I would test it using my device
>>>> and check if it really works because I don't see what could be wrong with
>>>> that series. I don't think that ST has changed something between HW
>>>> revision but I'm not able to locate on PCB what revision exactly is my
>>>> board (I guess ST hasn't written it on the soldermask).
>>>>
>>>>
>>>> Best
>>>> Bartek
>>>>
>>>>
>>>> בתאריך יום ד׳, 7 באוק׳ 2020 ב-22:27 מאת Bartosz Bilas <
>>>> b.bilas at grinn-global.com>:
>>>>
>>>>> Hi Shlomi,
>>>>>
>>>>> On 07.10.2020 21:13, Bartosz Bilas wrote:
>>>>> >
>>>>> > Hi Shlomi,
>>>>> >
>>>>> > On 07.10.2020 16:49, Shlomi Vaknin wrote:
>>>>> >> Adding support for wifi for stm32mp157c-dk2 is achieved by using
>>>>> >> another dts which includes the bindings for the wifi module.
>>>>> >> In addition, a txt file for the wifi firmware was added.
>>>>> >> This was copied from the yocto bsp layer of st.
>>>>> >>
>>>>> >> Signed-off-by: Shlomi Vaknin<shlomi.39sd at gmail.com>
>>>>> >> ---
>>>>> >> .../stm32mp157c-dk2/linux.config | 4 +-
>>>>> >> .../overlay/boot/extlinux/extlinux.conf | 2 +-
>>>>> >> .../brcmfmac43430-sdio.st,stm32mp157c-dk2.txt | 59
>>>>> +++++++++++++++++++
>>>>> >> .../stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts | 32 ++++++++++
>>>>> >> configs/stm32mp157c_dk2_defconfig | 7 ++-
>>>>> >> 5 files changed, 100 insertions(+), 4 deletions(-)
>>>>> >> create mode 100644
>>>>> board/stmicroelectronics/stm32mp157c-dk2/overlay/lib/firmware/brcm/
>>>>> brcmfmac43430-sdio.st,stm32mp157c-dk2.txt
>>>>> >> create mode 100644
>>>>> board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts
>>>>> >>
>>>>> >> diff --git a/board/stmicroelectronics/stm32mp157c-dk2/linux.config
>>>>> b/board/stmicroelectronics/stm32mp157c-dk2/linux.config
>>>>> >> index c03eb748b4..4beee3a708 100644
>>>>> >> --- a/board/stmicroelectronics/stm32mp157c-dk2/linux.config
>>>>> >> +++ b/board/stmicroelectronics/stm32mp157c-dk2/linux.config
>>>>> >> @@ -24,8 +24,6 @@ CONFIG_HIGHMEM=y
>>>>> >> CONFIG_FORCE_MAX_ZONEORDER=12
>>>>> >> CONFIG_SECCOMP=y
>>>>> >> # CONFIG_ATAGS is not set
>>>>> >> -CONFIG_ZBOOT_ROM_TEXT=0x0
>>>>> >> -CONFIG_ZBOOT_ROM_BSS=0x0
>>>>> >> CONFIG_ARM_APPENDED_DTB=y
>>>>> >> CONFIG_ARM_ATAG_DTB_COMPAT=y
>>>>> >> CONFIG_VFP=y
>>>>> >> @@ -45,6 +43,7 @@ CONFIG_UNIX=y
>>>>> >> CONFIG_INET=y
>>>>> >> CONFIG_CAN=y
>>>>> >> CONFIG_CAN_M_CAN=y
>>>>> >> +CONFIG_CFG80211=m
>>>>> >> CONFIG_DEVTMPFS=y
>>>>> >> CONFIG_DEVTMPFS_MOUNT=y
>>>>> >> CONFIG_SIMPLE_PM_BUS=y
>>>>> >> @@ -66,6 +65,7 @@ CONFIG_SMSC911X=y
>>>>> >> CONFIG_STMMAC_ETH=y
>>>>> >> CONFIG_DWMAC_DWC_QOS_ETH=y
>>>>> >> CONFIG_MDIO_BITBANG=y
>>>>> >> +CONFIG_BRCMFMAC=m
>>>>> >> CONFIG_INPUT_JOYDEV=y
>>>>> >> CONFIG_INPUT_EVDEV=y
>>>>> >> CONFIG_INPUT_TOUCHSCREEN=y
>>>>> >> diff --git
>>>>> a/board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf
>>>>> b/board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf
>>>>> >> index 5b7f56ee77..a6595971a8 100644
>>>>> >> ---
>>>>> a/board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf
>>>>> >> +++
>>>>> b/board/stmicroelectronics/stm32mp157c-dk2/overlay/boot/extlinux/extlinux.conf
>>>>> >> @@ -1,4 +1,4 @@
>>>>> >> label stm32mp157c-dk2-buildroot
>>>>> >> kernel /boot/zImage
>>>>> >> - devicetree /boot/stm32mp157c-dk2.dtb
>>>>> >> + devicetree /boot/stm32mp157c-dk2-wifi.dtb
>>>>> >> append root=/dev/mmcblk0p4 rootwait
>>>>> >> diff --git
>>>>> a/board/stmicroelectronics/stm32mp157c-dk2/overlay/lib/firmware/brcm/
>>>>> brcmfmac43430-sdio.st,stm32mp157c-dk2.txt
>>>>> b/board/stmicroelectronics/stm32mp157c-dk2/overlay/lib/firmware/brcm/
>>>>> brcmfmac43430-sdio.st,stm32mp157c-dk2.txt
>>>>> >> new file mode 100644
>>>>> >> index 0000000000..b36de8837f
>>>>> >> --- /dev/null
>>>>> >> +++
>>>>> b/board/stmicroelectronics/stm32mp157c-dk2/overlay/lib/firmware/brcm/
>>>>> brcmfmac43430-sdio.st,stm32mp157c-dk2.txt
>>>>> >> @@ -0,0 +1,59 @@
>>>>> >> +# NVRAM file for BCM943430WLSELG
>>>>> >> +# 2.4 GHz, 20 MHz BW mode
>>>>> >> +
>>>>> >> +# The following parameter values are just placeholders, need to be
>>>>> updated.
>>>>> >> +manfid=0x2d0
>>>>> >> +prodid=0x0726
>>>>> >> +vendid=0x14e4
>>>>> >> +devid=0x43e2
>>>>> >> +boardtype=0x0726
>>>>> >> +boardrev=0x1202
>>>>> >> +boardnum=22
>>>>> >> +macaddr=00:90:4c:c5:12:38
>>>>> >> +sromrev=11
>>>>> >> +boardflags=0x00404201
>>>>> >> +boardflags3=0x08000000
>>>>> >> +xtalfreq=37400
>>>>> >> +#xtalfreq=19200
>>>>> >> +nocrc=1
>>>>> >> +ag0=255
>>>>> >> +aa2g=1
>>>>> >> +ccode=ALL
>>>>> >> +
>>>>> >> +pa0itssit=0x20
>>>>> >> +extpagain2g=0
>>>>> >> +
>>>>> >> +#PA parameters for 2.4GHz, measured at CHIP OUTPUT
>>>>> >> +pa2ga0=-168,7161,-820
>>>>> >> +AvVmid_c0=0x0,0xc8
>>>>> >> +cckpwroffset0=5
>>>>> >> +
>>>>> >> +# PPR params
>>>>> >> +maxp2ga0=84
>>>>> >> +txpwrbckof=6
>>>>> >> +cckbw202gpo=0
>>>>> >> +legofdmbw202gpo=0x66111111
>>>>> >> +mcsbw202gpo=0x77711111
>>>>> >> +propbw202gpo=0xdd
>>>>> >> +
>>>>> >> +# OFDM IIR :
>>>>> >> +ofdmdigfilttype=18
>>>>> >> +ofdmdigfilttypebe=18
>>>>> >> +# PAPD mode:
>>>>> >> +papdmode=1
>>>>> >> +papdvalidtest=1
>>>>> >> +pacalidx2g=32
>>>>> >> +papdepsoffset=-36
>>>>> >> +papdendidx=61
>>>>> >> +
>>>>> >> +il0macaddr=00:90:4c:c5:12:38
>>>>> >> +wl0id=0x431b
>>>>> >> +
>>>>> >> +deadman_to=0xffffffff
>>>>> >> +# muxenab: 0x1 for UART enable, 0x2 for GPIOs, 0x8 for JTAG
>>>>> >> +muxenab=0x1
>>>>> >> +# CLDO PWM voltage settings - 0x4 - 1.1 volt
>>>>> >> +#cldo_pwm=0x4
>>>>> >> +
>>>>> >> +#VCO freq 326.4MHz
>>>>> >> +spurconfig=0x3
>>>>> >> diff --git
>>>>> a/board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts
>>>>> b/board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts
>>>>> >> new file mode 100644
>>>>> >> index 0000000000..89747d2b5f
>>>>> >> --- /dev/null
>>>>> >> +++
>>>>> b/board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts
>>>>> >> @@ -0,0 +1,32 @@
>>>>> >> +/dts-v1/;
>>>>> >> +
>>>>> >> +#include "stm32mp157c-dk2.dts"
>>>>> >> +
>>>>> >> +/ {
>>>>> >> + wifi_pwrseq: wifi-pwrseq {
>>>>> >> + compatible = "mmc-pwrseq-simple";
>>>>> >> + reset-gpios = <&gpioh 4 GPIO_ACTIVE_LOW>;
>>>>> >> + };
>>>>> >> +};
>>>>> >> +
>>>>> >> +/* Wifi */
>>>>> >> +&sdmmc2 {
>>>>> >> + arm,primecell-periphid = <0x10153180>;
>>>>> >> + pinctrl-names = "default", "opendrain", "sleep";
>>>>> >> + pinctrl-0 = <&sdmmc2_b4_pins_a>;
>>>>> >> + pinctrl-1 = <&sdmmc2_b4_od_pins_a>;
>>>>> >> + pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
>>>>> >> + non-removable;
>>>>> >> + st,neg-edge;
>>>>> >> + bus-width = <4>;
>>>>> >> + vmmc-supply = <&v3v3>;
>>>>> >> + mmc-pwrseq = <&wifi_pwrseq>;
>>>>> >> + #address-cells = <1>;
>>>>> >> + #size-cells = <0>;
>>>>> >> + status = "okay";
>>>>> >> +
>>>>> >> + brcmf: bcrmf at 1 {
>>>>> >> + reg = <1>;
>>>>> >> + compatible = "brcm,bcm4329-fmac";
>>>>> >> + };
>>>>> >> +};
>>>>> >> diff --git a/configs/stm32mp157c_dk2_defconfig
>>>>> b/configs/stm32mp157c_dk2_defconfig
>>>>> >> index bf7b9868b1..9c2e436244 100644
>>>>> >> --- a/configs/stm32mp157c_dk2_defconfig
>>>>> >> +++ b/configs/stm32mp157c_dk2_defconfig
>>>>> >> @@ -9,8 +9,13 @@ BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="5.8.13"
>>>>> >> BR2_LINUX_KERNEL_USE_CUSTOM_CONFIG=y
>>>>> >>
>>>>> BR2_LINUX_KERNEL_CUSTOM_CONFIG_FILE="board/stmicroelectronics/stm32mp157c-dk2/linux.config"
>>>>> >> BR2_LINUX_KERNEL_DTS_SUPPORT=y
>>>>> >> -BR2_LINUX_KERNEL_INTREE_DTS_NAME="stm32mp157c-dk2"
>>>>> >>
>>>>> +BR2_LINUX_KERNEL_CUSTOM_DTS_PATH="board/stmicroelectronics/stm32mp157c-dk2/stm32mp157c-dk2-wifi.dts"
>>>>> >> BR2_LINUX_KERNEL_INSTALL_TARGET=y
>>>>> >> +BR2_PACKAGE_LINUX_FIRMWARE=y
>>>>> >> +BR2_PACKAGE_LINUX_FIRMWARE_BRCM_BCM43XXX=y
>>>>> >> +BR2_PACKAGE_WIRELESS_REGDB=y
>>>>> >> +BR2_PACKAGE_WPA_SUPPLICANT=y
>>>>> >> +BR2_PACKAGE_WPA_SUPPLICANT_CLI=y
>>>>> >> BR2_TARGET_ROOTFS_EXT2=y
>>>>> >> BR2_TARGET_ROOTFS_EXT2_4=y
>>>>> >> BR2_TARGET_ROOTFS_EXT2_SIZE="120M"
>>>>>
>>>>> I suggest to add BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_MDEV to load
>>>>> firmware and driver automatically on boot.
>>>>>
>>>>> Unfortunately it doesn't work for me, see:
>>>>>
>>>>> [ 4.186415] cfg80211: Loading compiled-in X.509 certificates for
>>>>> regulatory database
>>>>> [ 4.237180] cfg80211: Loaded X.509 cert 'sforshee:
>>>>> 00b28ddf47aef9cea7'
>>>>> [ 4.300765] brcmfmac: brcmf_fw_alloc_request: using
>>>>> brcm/brcmfmac43430-sdio for chip BCM43430/1
>>>>> [ 5.389412] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
>>>>> clkctl 0x50
>>>>> [ 6.407710] brcmfmac: brcmf_sdio_htclk: HT Avail timeout (1000000):
>>>>> clkctl 0x50
>>>>>
>>>>> Google says that it could be due to wrong nvram file configuration but
>>>>> I
>>>>> assume that you have run it successfully?
>>>>>
>>>>> # ifconfig -a
>>>>> eth0 Link encap:Ethernet HWaddr 00:80:E1:42:56:44
>>>>> BROADCAST MULTICAST MTU:1500 Metric:1
>>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>>> collisions:0 txqueuelen:1000
>>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>> Interrupt:49 Base address:0xe000
>>>>>
>>>>> lo Link encap:Local Loopback
>>>>> inet addr:127.0.0.1 Mask:255.0.0.0
>>>>> inet6 addr: ::1/128 Scope:Host
>>>>> UP LOOPBACK RUNNING MTU:65536 Metric:1
>>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>>> collisions:0 txqueuelen:1000
>>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>>
>>>>> sit0 Link encap:IPv6-in-IPv4
>>>>> NOARP MTU:1480 Metric:1
>>>>> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
>>>>> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
>>>>> collisions:0 txqueuelen:1000
>>>>> RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
>>>>>
>>>>> #
>>>>>
>>>>> As you can see there is no wlan0 interface.
>>>>>
>>>>> Best
>>>>> Bartek
>>>>>
>>>>
>>>> _______________________________________________
>>>> buildroot mailing listbuildroot at busybox.nethttp://lists.busybox.net/mailman/listinfo/buildroot
>>>>
>>>>
>> _______________________________________________
>> buildroot mailing listbuildroot at busybox.nethttp://lists.busybox.net/mailman/listinfo/buildroot
>>
>>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20201012/fb1e810e/attachment-0002.html>
More information about the buildroot
mailing list